Focused ion beam–time-of-flight secondary ion mass spectrometry (FIB–ToF-SIMS) detects sputtered, ionized surface constituents during FIB irradiation. It yields mass-to-charge spectra and spatially resolved ion-intensity maps; repeated sputtering provides depth profiles or 3D chemical volumes. This is destructive microanalysis. [R2,R4]
The TOFWERK fibTOF analyzer records a broad mass spectrum rather than scanning isolated nominal masses one at a time. It can complement SEM imaging, energy-dispersive X-ray spectroscopy (EDS), and EBSD, particularly for light elements (e.g., Li, B), halogens, and isotopic distributions. [R2,R3,R15]
Elemental and isotopic mapping across particles, layers, precipitates and interfaces; strengths include light elements and species often challenging for conventional EDS. [R2,R4]
Small-region depth profiling of multilayers, coatings, interfacial contamination and dopant distributions; sputter-induced mixing and topography limit real depth resolution. [R2,R4]
3D chemical visualization via sputter-and-measure imaging, with drift correction and crater/voxel metrology needed for interpretable geometry. [R2,R4]
Gas-assisted FIB–ToF-SIMS for signal enhancement and polarity control is reported in literature, but responses depend on sample chemistry and gas settings; it is not a universal sensitivity boost. [R5]
Xe+: potentially attractive for high-throughput sputtering, but large beam currents, mixing and erosion-induced roughness can compromise finely resolved profiles. One cannot infer SIMS sensitivity from milling speed alone. [R1,R2]
Ar+: useful candidate when reactive implantation is undesirable; TOFWERK identifies light ions, including Ar and Ga, as plausible choices when spatial resolution is prioritized. Validate sensitivity in the target matrix. [R2]
O+: may increase yields of certain positive secondary ions via surface oxygen chemistry, but can modify oxygen-containing species and masks native oxygen distributions. Magnitude and sign of the effect depend on element, matrix and conditions. [R2,R5]
N+: material chemistry may change through nitrogen incorporation/nitridation (documented for Si), potentially confounding intrinsic nitrogen and compound-ion signals; do not claim it is the optimal nitrogen-imaging ion. [R1]
Important: the specific five-ion comparison in Brogden et al. is a sputter-yield/texture study, not a calibrated head-to-head fibTOF sensitivity benchmark across five ions. [R1]
Secondary-ion signal is not proportional to concentration without qualification: relative sensitivity factors are matrix dependent; positive/negative polarity, surface chemistry, chamber residual gases, beam current, and local charging can change response. TOFWERK explicitly notes dependence on vacuum history and scan pattern. [R2,R4]
Absolute or semi-quantitative results require matrix-matched reference standards and a calibrated measurement protocol; normalize cautiously. Isotope ratios also require resolving interferences, accounting for detection statistics and validating instrumental fractionation. [R2,R4]
Structural molecular ions from organic samples may not survive energetic dynamic FIB-SIMS in useful abundance. Do not describe FIB–ToF-SIMS as routine intact-molecule identification under ordinary high-energy FIB conditions. [R2]
TOFWERK fibTOF product specifications list mass range 1–500 Th, mass resolving power M/ΔM (full width at half maximum) greater than 700, parts-per-million-scale detection limits, approximately 50 nm lateral resolution and approximately 10 nm depth resolution, with asterisked dependence on FIB performance. These are manufacturer-level figures, not guaranteed specimen-level outcomes. [R3,R15]
Report experimentally established mass resolution for peaks of interest, pixel sampling, analyzed depth or crater dimensions, counts/dose, detection limits in the particular matrix (if calibrated), and the standards/blank used. [R2,R4]
No universal primary-ion ranking, detection limit, depth resolution, sputter-to-concentration conversion, or five-ion optimal-use matrix can be justified without calibration data. Especially for O+ and N+, any improved yield must be distinguished from chemical modification of the specimen. [R1,R2,R5]
Science Education and Research Center (SERC)
Room 008
Publications using EM Lab data must acknowledge the facility.
See here.